How to wrap a Mobius Coil for Succor Punch. Pro Tips !

Sensei · Last edited by Sensei on Sat Jul 30, 2011 4:33 am; edited 10 times in total

A picture tutorial on wrapping a mobius coil for Succor Punch, Power Wand and powered orgonite devices.

I wrap coils around crystals nearly every day and have for years. Here is how to do it.

The wire is stranded 26 Ga. wire. I like this size wire for wrapping small to medium sized crystals. I twisted it counter clockwise with a drill until the wire was at about 45 degree angle and smooth to the touch. The crystal is a Lemurian from Brazil.

Tool of choice (Needed to open a channel under the coil for new wraps to pass through), is a small flat head screwdriver, available at all dollar stores in a pack of mini screwdrivers for about $2). IMPORTANT, when using a small screwdriver you must sand the corners to a slight rounded shape so that it slides smoothly through the wires and does not cut them with a sharp edge.

How much wire is needed ?
As you wrap from the unfinished end to the loop end, the wire has to be the correct length ...or it will either be too short to finish or too long for the crystal. Knowing how much wire to use is essential and can be figured very easily and exactly.

Starting with the loop end of the wire at the top of the crystal wrap the entire crystal in a spiral manner to the end.

This is exactly how much wire that you need. Place a sharp bend in it to mark the end, this will be your starting point. (The End marks the Beginning ?? Just too Zen, lol.)

Holding the crystal in your left hand , with the tip pointed to the left. Secure the loose end(Later to be attached to a frequency generator) with two fingers to keep it tight. The wire on the right is the loose end, the loop end (left) goes OVER the crystal then under towards you.

Continue around the crystal and GO OVER the loose end wire.

Put your tool under the wire. With the tool tip on the crystal face, gently lift the handle forming a channel under the wrap for the wire to pass through. This will become very important as the wrap proceedes and the coil gets tighter.

Pass the loop end under the coil.

After pulling the wire through the coil, again take it OVER the crystal then under towards you.

Go over the coil, over the loose end Then under the coil. Pass the wire over the coil with the loop end going next to the place where it crossed over on the previous wrap, That crossover point is towards you, and will give a flat wrap if correct.

Continue to wrap as before until about 1/2 of the wire is used and it gets difficult to pass the wire under the now growing coil. (or 1/3 of the wire if making a 3 segment coil).

Then take the wire up the crystal, bend it 90 degrees and start another coil, same direction as before.

Cross over where the wire goes straight THEN under to form a new coil segment.

It works the same way for larger crystals.

Continue until the wire is used up and tuck the loop end under the coil and glue it to secure it in place. I use a super glue gel with a spray instant hardener.

It is a Very good idea to then put a shrink tube on the wire snugged up to the coil. This will prevent the wire from breaking at the stress point during use for many years.

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com

VibratingPickle · Member Joined: 10 Apr 2011 Posts: 610

Nice job on the tutorial. Quality pics.

Is that a stick on the end of the SP? I am curious what that is for?

Sensei · Posted: Sat Jul 30, 2011 1:06 am Post subject:

Well, since this crystal is all wrapped, let's do something with it.

Add a little resin, let cure and add some amethyst and a little more resin.

How about a layer of 24 karat gold/resin.

A layer of blue tinted resin with aluminum and brass might be nice.

The final layer is Nano Iron, and Lemurian crystals, lab reduced to nano size.

Wait a few hours and...

Looking down the barrel.

A Home Shield soon to be on the way to it's new Home

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com

vortexlady · Member Joined: 09 Jul 2011 Posts: 4 Location: south texas

Absolutely beautiful. I am awe struck! Thank you for that step by step of wrapping the crystal. One day I will try that. That stick idea could be used for anything. Like use on my bismuth pyrmids. Thanks Dennis and Lena for always giving us great ideas.

vortexlady · Member Joined: 09 Jul 2011 Posts: 4 Location: south texas

Where do you get the 24kt gold flecks? Thanks for your help!

Sensei · Posted: Tue Aug 02, 2011 5:29 am Post subject:

Google 24 k gold leaf (loose) for vendors.

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com

deisel · Posted: Tue Aug 02, 2011 12:10 pm Post subject:

Very good tutorial, thank you.

GodsPredeces0r · Posted: Wed Aug 10, 2011 5:07 am Post subject:

Thanks for the tutorial, I originally was thinking i was going to wrap the wire loosely and then snug it onto the crystal, but you made it make sense in the wrapping process, But i cant see, you do that wrap inside and around 3 times ?
Or is in the particular crystal you are using the wire for the mobius coil wraping go in and around ontiself only 2 times?

And thanks for the 24 kt gold leaf idea, Gold is a wonderful healing color.
I wonder if i can take the leaf and instead of crumbling into the resin just apply it on the walls of the pyramid/shape used.

Sensei · Posted: Wed Aug 10, 2011 5:53 am Post subject:

Wrap a couple of crystals for yourself, then ask questions.

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com

cutter · Member Joined: 22 Jan 2011 Posts: 469 Location: europe

I have a question on the wire you use.

you say 26 ga wire. I googled that and in metric thats a wire with 0.14 mm core multiple strands.
did you ever use thinner wire?
I used the same stuff but find it difficult to wrap small crystals with em.
would it be possible to use thinner wire? (am an electronics noob)
or would that become a problem with the current running through from the zapper?
"burning the wire?"
I found some flexible decoder wire online which is even thinner 0.05 mm core, outer diameter 0.8 mm.
was thinking of trying that....

Sensei · Posted: Tue Aug 16, 2011 7:33 pm Post subject:

Thinner wire should be fine, keeping in mind that the thinner the wire, the more prone it is to breaking at any point that is moved regularly or stressed.

Use lots of shrink tubing to reinforce those areas where it is likely to break after extended use.

Sєηѕєι
_________________
Thank you for supporting WarriorMatrix at:
http://www.OrgoneCrystals.com
and
http://www.LemurianCrystal.com
Please, share...
http://www.OrgoniteInfo.com

cutter · Member Joined: 22 Jan 2011 Posts: 469 Location: europe

ok thank you
I will wrap it, cut the end, then check if its intact.
solder the end back together ad a piece of shrink tube.
dont worry about extended use..... I will cast them in raisin. Very Happy

cutter · Member Joined: 22 Jan 2011 Posts: 469 Location: europe

how did I do?

your pyramid obviously inspired me:

wrapped crystal, copper and crystal powder, copper chavings, bronze , aluminium, some more crystals amethyst,roze quartz, hematite and black tourmaline.

cutter · Member Joined: 22 Jan 2011 Posts: 469 Location: europe

by the way, had no intention of "hacking this post"!
would it be more apropriate to make a new topic in this case? (just asking)

Sensei · Posted: Wed Dec 21, 2011 4:50 am Post subject: